Ihr Warenkorb ist leer
 

Romeo V2-All in one Controller

34.20EUR
inkl. 19% MwSt.
zzgl. Versandkosten

 

 

 

Romeo-All in one Controller (ATmega32u)

Nachfolgemodell des bewährten Romeo mit zusätzlichen Features.

Romeo ist ein Arduino Leonardo kompatibler All-in-One-Mikrocontroller speziell konzipiert für die Robotik-Anwendung.Romeo kann problemlos mit den meisten Arduino Shields erweitert werden.Der integrierte 2-Weg-DC-Motor-Treiber plus XBee Sockel ist eine einfache und kompakte Basis für Roboter-Projekte. Servos können direkt am Board angesteckt werden  (Extra Anschlussklemmen für Servo Power)

Durch die Verwendung des Atmega32u steht die serielle Schnittstelle des Mikrocontrollers voll zur Verfügung für z.B XBee

Eine grosse Verbesserung ist die Stromversorgung über einen Schaltregler, das heisst hoher Wirkungsgrad und bis zu 2A Ausgangsstrom bei weitem Eingangsspannungsbereich (7-23V DC)

 

Introduction  

RoMeo V2[R3]is an All-in-One Arduino compatible microcontroller especially designed for robotics applications from DFRobot. The Romeo benefits from the Arduino open source platform, it is supported by thousands of open source codes, and can easily be expanded with Arduino Shields. The integrated 2 way DC motor driver and Xbee socket allows you to start your project immediatly without the need for an additional motor driver or wirless shield. 
 
Another improvement of Romeo V2 is that it supports stepper motor control. 
 
The RoMeo V2[R3] behaves like Arduino Leonardo based on the ATmega32u4 chip,You can program it directly from the Arduino IDE 1.0.1 or later version.Because of the ATmega32U4 as its sole microcontroller, allows the RoMeo V2 to be simpler to use.Also,The 32U4 is handling the USB directly, code libraries are available which allow the board to emulate a computer keyboard, mouse, and more using the USB-HID protocol!  The best advantage is that ATmega32u4 has two serial ports which allows you uploading sketches without removing wireless modules.  Debuging is no longer a pain work. 
 
Romeo V2 also improves the power supply, it has now a switch to select power source either from USB or external power. 
 
Warning:The analog sensor port pin mapping on RoMeo v2 is different from the old version.  Please select Arduino Leonardo board when using Arduino IDE.
 
 
Specification
  • DC Supply:USB Powered or External 6V~23V DC
  • DC Output:5V(2A) / 3.3V DC
  • Motor driver Continuous Output Current:2A
  • Microcontroller:ATmega32u4
  • Bootloader: Arduino Leonardo
  • Compatible with the Arduino R3 pin mapping
  • Analog Inputs: A0-A5, A6 - A11 (on digital pins 4, 6, 8, 9, 10, and 12)
  • PWM: 3, 5, 6, 9, 10, 11, and 13. Provide 8-bit PWM output
  • 5 key inputs for testing
  • Auto sensing/switching external power input
  • Serial Interface
    • TTL Level
    • USB
  • Support Male and Female Pin Header
  • Built-in Xbee socket
  • Integrated sockets for APC220 RF Module and DF-Bluetooth Module
  • Three I2C/TWI Interface Pin Sets
  • Two way Motor Driver with 2A maximum current
  • One Stepper Motor Drive with 2A maximum current
  • Size:89x84x14mm
 
Improvement compared with Romeo v1.1
  • Wide operating input voltage
  • Directly support Xbee and XBee form factor wifi,bluetooth and RF modules
  • ON/OFF switch to control the system power from extermal motor power
  • 3 Digital I/O extension(D14-D16)
  • S1-S5 switch replace jump cap
  • Micro USB instead of A-B USB connector
  • Analog sensor extension port: Orange for Signal,Red for Vcc,Black for GND
 
Shipping List
  • Romeo V2-All in one Controller        (1 unit)
Documents

Anzahl:

  • Artikelnummer: DFR0225
  • 0 Stück auf Lager
  • Hergestellt von: DFRobot


Dieser Artikel wurde am Montag, 13. Mai 2013 im Shop aufgenommen.

 
     
Find us on Facebook PayPal Accepted

Copyright © 2024 komputer.de. Powered by Zen Cart